Brookfield Engineering Laboratories, Inc. Page 1 Manual No. M/85-150-P700BROOKFIELD DIAL VISCOMETEROperating InstructionsManual No. M/85-150-P700M
Brookfield Engineering Laboratories, Inc. Page 10 Manual No. M/85-150-P700Remove the sample cup and attach the cone to the Viscometer (Note: left
Brookfield Engineering Laboratories, Inc. Page 11 Manual No. M/85-150-P700Turn the adjustment ring to the right (counterclockwise as you look down
Brookfield Engineering Laboratories, Inc. Page 12 Manual No. M/85-150-P700When you are satisfied the pins are just hitting (by observing acceptabl
Brookfield Engineering Laboratories, Inc. Page 13 Manual No. M/85-150-P700Each of the five available cones has a specific sample volume, as shown
Brookfield Engineering Laboratories, Inc. Page 14 Manual No. M/85-150-P7004) Attach sample cup to viscometer and allow approximately 15 minutes fo
Brookfield Engineering Laboratories, Inc. Page 15 Manual No. M/85-150-P700The ratio of (ωr) and (c) is a constant for any value of (r). Since (c)
Brookfield Engineering Laboratories, Inc. Page 16 Manual No. M/85-150-P700Wells-Brookfield Cone/Plate Viscometer Full Scale Ranges3.0° CONE SPINDL
Brookfield Engineering Laboratories, Inc. Page 17 Manual No. M/85-150-P700Viscometer Ranges in Centipoise (1 cP = 1 mPa•s)Viscosity = Dial Reading
Brookfield Engineering Laboratories, Inc. Page 18 Manual No. M/85-150-P700APPENDIX B - Viscosity RangesLV Series Viscometers with Spindles #1 - #4
Brookfield Engineering Laboratories, Inc. Page 19 Manual No. M/85-150-P700UL AdapterCone/Plate ViscometerHelipath with T-Bar Spindles YULA-15 or 1
Brookfield Engineering Laboratories, Inc. Page 2 Manual No. M/85-150-P700TABLE OF CONTENTS I. INTRODUCTION ...
Brookfield Engineering Laboratories, Inc. Page 20 Manual No. M/85-150-P700APPENDIX C - Variables in Viscosity MeasurementsAs with any instrument m
Brookfield Engineering Laboratories, Inc. Page 21 Manual No. M/85-150-P700A repeatable viscosity test should control or specify the following:1) T
Brookfield Engineering Laboratories, Inc. Page 22 Manual No. M/85-150-P700APPENDIX D - Calibration ProceduresThe accuracy of the Dial Viscometer i
Brookfield Engineering Laboratories, Inc. Page 23 Manual No. M/85-150-P700Brookfield Engineering Laboratories does not recertify Viscosity Standar
Brookfield Engineering Laboratories, Inc. Page 24 Manual No. M/85-150-P700Calibration Procedure for a Thermosel SystemWhen a Thermosel System is u
Brookfield Engineering Laboratories, Inc. Page 25 Manual No. M/85-150-P7005) After 1 hour, check the temperature of the viscosity standard fluid w
Brookfield Engineering Laboratories, Inc. Page 26 Manual No. M/85-150-P700D2. Consult with Brookfield or an authorized dealer to determine which
Brookfield Engineering Laboratories, Inc. Page 27 Manual No. M/85-150-P700Contact the Brookfield technical sales department or your local Brookfie
Brookfield Engineering Laboratories, Inc. Page 28 Manual No. M/85-150-P700RV Guardleg LV GuardlegFigure D1
Brookfield Engineering Laboratories, Inc. Page 29 Manual No. M/85-150-P700Figure E1 APPENDIX E - Models A & A-E Laboratory StandsUnpackingChec
Brookfield Engineering Laboratories, Inc. Page 3 Manual No. M/85-150-P700 I. INTRODUCTIONThe Brookfield Dial Viscometer measures fluid viscosity
Brookfield Engineering Laboratories, Inc. Page 30 Manual No. M/85-150-P700Remove the three (3) leveling screws from the base and discard the packi
Brookfield Engineering Laboratories, Inc. Page 31 Manual No. M/85-150-P700 APPENDIX F - Fault Diagnosis and TroubleshootingListed are some of the
Brookfield Engineering Laboratories, Inc. Page 32 Manual No. M/85-150-P700Inaccurate Readings❏ Verify spindle, speed and model selection❏ Verify t
Brookfield Engineering Laboratories, Inc. Page 33 Manual No. M/85-150-P700 APPENDIX G - Warranty Repair and ServiceWarrantyBrookfield Viscometers
Brookfield Engineering Laboratories, Inc. Page 34 Manual No. M/85-150-P700For repair or service in the United States return to:Brookfield Engin
Brookfield Engineering Laboratories, Inc. Page 35 Manual No. M/85-150-P700VISCOSITY TEST REPORTSAMPLE MODEL SPINDLE RPMDIAL READINGFACTORVISCOSITY
Brookfield Engineering Laboratories, Inc. Page 4 Manual No. M/85-150-P700 I.2 UtilitiesInput Voltage: 115 VAC or 230 VACInput Frequency: 50 or 60
Brookfield Engineering Laboratories, Inc. Page 5 Manual No. M/85-150-P700 II. GETTING STARTED II.1 OperationThe Brookfield Viscometer is powered b
Brookfield Engineering Laboratories, Inc. Page 6 Manual No. M/85-150-P700fluid surface, and bring the spindle to an upright position and thread on
Brookfield Engineering Laboratories, Inc. Page 7 Manual No. M/85-150-P700 .5 200 .5 800 .5 2K.5 4K.5 8K.5 20K.5 80K1 100 1 400 1 1K12K14K110K140K2
Brookfield Engineering Laboratories, Inc. Page 8 Manual No. M/85-150-P700II.3Considerations for Making MeasurementsIn taking viscosity measurement
Brookfield Engineering Laboratories, Inc. Page 9 Manual No. M/85-150-P700 APPENDIX A - Cone/Plate Viscometer Set-UpThe Wells-Brookfield Dial Visco
Commentaires sur ces manuels